INTIMIDATOR Пистолет Головоломка
Комментарии автора сего девайса:
"INTIMIDATOR Пистолет Головоломка – пистолет для одиночного выстрела в упор 45-ым калибром, уникальное предложение как средство самообороны.
В молодости, я был впечатлен использованием пистолета Scaramanga в фильме про Джеймса Бонда «Человек с Золотым пистолетом» ("The Man with the Golden Gun", 1974 г). С недавних пор, я стал думать о моем собственном дизайне. INTIMIDATOR Пистолет Головоломка - задумывался, как обычный пистолетик 25 калибра, но со временем мои идеи, привели меня к более устрашающему 45 калибру.
Конструкция включает все необходимое для сборки Пистолета Головоломки. В конструкцию интегрирован набор различных инструментов, необходимых принадлежностей, пули 45 калибра, стандартный прицел, лазерный прицел, боеприпасы и чистящие средства."
GarE Maxton
The INTIMIDATOR, 20,32 Высота x 12,7 ширина x 10,16 глубина (размеры представлены в см).
Металлические части имеют 6 различных цветов.
В производстве использованы следующие металлы: медь, нержавеющая сталь, алюминий, бронза и магний.
125 частей пистолета :)))
The INTIMIDATOR PUZZLE PISTOL (с лазерным прицелом)
INTIMIDATOR (стандартный прицел).
|
The key is used to open the puzzle block by magnetically attracting the lever piece.
Then the lever is pushed down to allow removal of the top piece.
|
This customized hex tool is hidden inside the sculpture.
|
The puzzle key is unusable unless the top cover is removed. The separation
line is quite subtle so it's not obvious that it breaks down into two pieces.
The key (left) with the cover removed.
|
Ammunition can be stored within the sculpture; shown here is a 45 Caliber Bullet, a Black Powder Pellet and a 209 Shotgun Primer.
|
The gun powder pellets are stored in this small brass case.
The top slides off and the pellets can be removed.
|
The shotgun primers are safely stored in these bolted together puzzle parts.
The top piece slides off after the bolt is removed allowing access to the 3 primers.
|
These two interesting shaped parts create a subassembly with a hole that fits around another piece of the sculpture.
|
This subassembly requires one piece to be turned inside the next.
The subassembly shown ready to install.
|
The handle grips and sight mount are embedded in special enclosure pieces in the sculpture.
|
There is a special part made to retain the steel firing pin inside the firing pin assembly so it doesn't fall out.
The part is removed before installing the hammer spring assembly and is also used as a tool to remove spent primers from the breach plug.
|
The barrel chamber reinforcement bushing encloses the hammer spring assembly.
The hammer spring assembly (left), the barrel chamber reinforcement bushing (center) and a threaded adapter (right).
|
The threaded knob that retains the hex bits inside the hex tool becomes the hammer weight.
|
The handle of the ramrod can be seen on the left as we take the sculpture apart.
The hex tool is located in the round hole on the right.
The handle of the pistol is revealed in the center.
A brass bullet adapter is added to complete the ramrod.
|
The barrel is a modified Green Mountain 45 caliber rifled 1:20 Twist .009" Groove Octagon barrel (left), the breach plug with gun grease on threads (right front) and the bronze barrel reinforcement bushing (right rear).
The barrel fully assembled.
|
The barrel rifling by Green Mountain - 1:20 Twist.
|
The sculpture before application of the patina.
|
Intimidator Nameplate and Serial Number.
National Firearms Act Stamp for this pistol.
|
Manufacturer's signature dated 2010 |
Комментарии